1 C3D16060D silicon carbide schottky diode z -r ec ? r ectifier features ? 600-volt schottky rectifer ? zero reverse recovery current ? zero forward recovery voltage ? high-frequency operation ? temperature-independent switching behavior ? extremely fast switching ? positive temperature coeffcient on v f benefts ? replace bipolar with unipolar rectifers ? essentially no switching losses ? higher effciency ? reduction of heat sink requirements ? parallel devices without thermal runaway applications ? switch mode power supplies ? power factor correction ? solar inverters ? motor drives ? electric vehicle charger package to-274-3 maximum ratings (t c =25c unless otherwise specifed) symbol parameter value unit test conditions note v rrm repetitive peak reverse voltage 600 v v rsm surge peak reverse voltage 600 v v dc dc blocking voltage 600 v i f continuous forward current (per leg/device) 23/46 11/22 8/16 a t c =25?c t c =135?c t c =150?c see fig. 3 i frm repetitive peak forward surge current (per leg/device) 57/114 36/72 a t c =25?c, t p = 10 ms, half sine wave, d=0.3 t c =110?c, t p =10 ms, half sine wave, d=0.3 i fsm non-repetitive peak forward surge current (per leg/device) 80/160 60/120 a t c =25?c, t p = 10 ms, half sine wave, d=0.3 t c =110?c, t p =10 ms, half sine wave, d=0.3 i fsm non-repetitive peak forward surge current (per leg/device) 220/440 a t c =25?c, t p = 10 s, pulse p tot power dissipation (per leg) 100* 43* w t c =25?c t c =110?c t j , t stg operating junction and storage temperature -55 to +175 ?c to-247 mounting torque 1 8.8 nm lbf-in m3 screw 6-32 screw part number package marking C3D16060D to-247-3 c3d16060 * per leg, ** per device v rrm = 600 v i f ( t c =135?c) = 22 a** q c = 42 nc** C3D16060D rev. a
2 6 7 8 9 10 forward current (a) forward characteristics 0 1 2 3 4 5 0.0 0.5 1.0 1.5 2.0 2.5 i f forward current (a) v f forward voltage (v) 60 70 80 90 100 reverse current (ua) reverse characteristics 0 10 20 30 40 50 0 100 200 300 400 500 600 700 800 900 1000 i r reverse current (ua) v r reverse voltage (v) electrical characteristics (per leg) symbol parameter typ. max. unit test conditions note v f forward voltage 1.6 1.9 1.8 2.4 v i f = 8 a t j =25c i f = 8 a t j =175c i r reverse current 10 20 50 200 a v r = 600 v t j =25c v r = 600 v t j =175c q c total capacitive charge 21 nc v r = 600 v, i f = 8a d i /d t = 500 a/ s t j = 25c c total capacitance 441 39 33 pf v r = 0 v, t j = 25c, f = 1 mhz v r = 200 v, t j = 25?c, f = 1 mhz v r = 400 v, t j = 25?c, f = 1 mhz note: 1. this is a majority carrier diode, so there is no reverse recovery charge. thermal characteristics symbol parameter typ. unit r jc thermal resistance from junction to case 1.5 * 0.75 ** c/w * per leg, ** per device typical performance (per leg) figure 1. forward characteristics figure 2. reverse characteristics v r reverse voltage (v) i r reverse current ( a) t j = 25c t j = 75c t j = 1 25c t j = 175c 100 90 80 70 60 50 40 30 20 10 0 0 100 200 300 400 500 600 700 800 900 1000 10 9 8 7 6 5 4 3 2 1 0 0.0 0.5 1.0 1.5 2.0 2.5 v f forward voltage (v) i f forward current (a) t j = 25c t j = 75c t j = 1 25c t j = 175c C3D16060D rev. a
3 40 50 60 peak forward current (a) c3d08060 current derating 0 10 20 30 25 50 75 100 125 150 175 i f(peak) peak forward current (a) tc case temperature ( c) figure 3. current derating figure 4. capacitance vs. reverse voltage figure 5. transient thermal impedance typical performance (per leg) 60 50 40 30 20 10 0 25 50 75 100 125 150 175 i f(peak) peak forward current (a) 20% duty* 30% duty* 50% duty* 70% duty* dc t c case temperature ( c ) * frequency > 1khz 1.0e-03 1.0e-02 1.0e-01 1.0e+00 1.0e+01 1.e-07 1.e-06 1.e-05 1.e-04 1.e-03 1.e-02 1.e-01 1.e+00 time (s) zth (c/w) 1 10 100 1000 v r reverse voltage (v ) 250 300 350 400 450 c capacitance (pf) capacitance vs. reverse voltage 0 50 100 150 200 250 1 10 100 1000 c capacitance (pf) v r reverse voltage (v) C3D16060D rev. a
4 power dissipation (w) t c case temperature ( c ) figure 6. power derating typical performance (per leg) 110 100 90 80 70 60 50 40 30 20 10 0 power dissipation (w) t c case temperature ( c ) 25 50 75 100 125 150 175 60.0 70.0 80.0 90.0 100.0 110.0 power dissipation (w) 0.0 10.0 20.0 30.0 40.0 50.0 60.0 25 50 75 100 125 150 175 power dissipation (w) t c case temperature (c) diode model (per leg) v t r t diode model csd10060 vf t = v t + if*r t v t= 0.92 + (t j * - 1.35*10 - 3 ) r t= 0.052 + (t j * 0.29*10 - 3 ) note: t j = diode junction temperature in degrees celsius vf t = v t +if*r t v t = 0.93+(t j * -9.3*10 -4 ) r t = 0.058+(t j * 5.7*10 -4 ) C3D16060D rev. a
5 recommended solder pad layout package dimensions package to-247-3 pos inches millimeters min max min max a .605 .635 15.367 16.130 b .800 .831 20.320 21.10 c .780 .800 19.810 20.320 d .095 .133 2.413 3.380 e .046 .052 1.168 1.321 f .060 .095 1.524 2.410 g .215 typ 5.460 typ h .175 .205 4.450 5.210 j .075 .085 1.910 2.160 k 6? 21? 6? 21? l 4? 6? 4? 6? m 2? 4? 2? 4? n 2? 4? 2? 4? p .090 .100 2.286 2.540 q .020 .030 .508 .762 r 9? 11? 9? 11? s 9? 11? 9? 11? t 2? 8? 2? 8? u 2? 8? 2? 8? v .137 .144 3.487 3.658 w .210 .248 5.334 6.300 x .502 .557 12.751 14.150 y .637 .695 16.180 17.653 z .038 .052 0.964 1.321 aa .110 .140 2.794 3.556 bb .030 .046 0.766 1.168 cc .161 .176 4.100 4.472 w x y z aa bb cc to-247-3 note: recommended soldering profles can be found in the applications note here: http://www.cree.com/power_app_notes/soldering part number package marking C3D16060D to-247-3 c3d16060 C3D16060D rev. a
6 6 C3D16060D rev. a copyright ? 2013 cree, inc. all rights reserved. the information in this document is subject to change without notice. cree, the cree logo, and zero recovery are registered trademarks of cree, inc. cree, inc. 4600 silicon drive durham, nc 27703 usa tel: +1.919.313.5300 fax: +1.919.313.5451 www.cree.com/power ? rohs compliance the levels of rohs restricted materials in this product are below the maximum concentration values (also referred to as the threshold limits) permitted for such substances, or are used in an exempted application, in accordance with eu directive 2011/65/ec (rohs2), as implemented january 2, 2013. rohs declarations for this product can be obtained from your cree representative or from the product documentation sections of www.cree.com. ? reach compliance reach substances of high concern (svhcs) information is available for this product. since the european chemi - cal agency (echa) has published notice of their intent to frequently revise the svhc listing for the foreseeable future,please contact a cree representative to insure you get the most up-to-date reach svhc declaration. reach banned substance information (reach article 67) is also available upon request. ? this product has not been designed or tested for use in, and is not intended for use in, applications implanted into the human body nor in applications in which failure of the product could lead to death, personal injury or property damage, including but not limited to equipment used in the operation of nuclear facilities, life-support machines, cardiac defbrillators or similar emergency medical equipment, aircraft navigation or communication or control systems, air traffc control systems, or weapons systems. notes
|
